Wall Sawing and Wall Saw Cutting in Qatar
Cuts up to 730mm deep through reinforced concrete walls and slabs with a track-mounted diamond saw. Send the opening dimensions and wall thickness for a quote.
Wall sawing at North Gate Mall for Habtoor Leighton and at Milaha Tower.
Wall sawing in Qatar with a track-mounted diamond saw: straight cuts up to 730mm deep through reinforced concrete walls, slabs and beams. The track is bolted to the surface and the operator runs the blade by remote control, so the cut stays on the marked line. Timing depends on wall thickness, reinforcement, access and section removal.
The usual jobs are door and window openings, lift shaft changes, service risers and HVAC openings in occupied Doha buildings. Where an opening must not be overcut, we finish the inside corners with core holes. Beyond 730mm, or where a blade cannot reach, we use wire sawing.
How does wall sawing work, step by step?
Survey & Layout
Our team surveys the wall, marks the cut lines, and runs a GPR scan on request to identify rebar, conduits and post-tension cables within the concrete. We recommend the scan where cables are suspected.
Track Installation
A steel guide track is bolted to the wall surface. The wall saw unit is mounted on the track, which keeps the cut straight and aligned from start to finish.
Diamond Blade Cutting
The diamond blade is engaged and guided along the track with continuous water cooling. The operator controls speed, depth, and feed rate remotely for optimal cut quality.
Section Removal & Finish
The cut concrete section is supported and lifted out so it cannot fall uncontrolled. The opening edges are clean, ready for frame installation or finishing.
Cleanup & Disposal
All debris, slurry, and cut sections are removed from the site. The work area is cleaned thoroughly, and waste is disposed of in compliance with Qatar regulations.
What is wall sawing used for?
Door & Window Openings
Creating new doorways and window openings in existing concrete walls for renovations, fit-outs, and building modifications.
Elevator Shafts
Cutting precise openings for new elevator installations in existing buildings, including shaft walls and machine room access.
Staircase Openings
Creating openings in floor slabs and walls for new staircase installations, emergency exits, and access modifications.
HVAC Duct Openings
Rectangular and square openings for air conditioning duct routes, ventilation shafts, and mechanical service penetrations.
Renovation Modifications
Removing wall sections, enlarging openings, and creating pass-throughs for commercial and residential renovation projects.
Structural Alterations
Controlled removal of concrete sections for structural strengthening, retrofit work, and building repurposing projects.
How thick a wall can you cut?
| Specification | Details |
|---|---|
| Maximum Cut Depth | Up to 730mm |
| Blade Technology | Industrial diamond blades for concrete and heavy rebar |
| Operation | Remote-controlled for operator safety |
| Cut Orientations | Horizontal, vertical, and inclined cuts |
| Precision | Cuts within a few millimetres of the marked line |
| Cooling System | Continuous water supply with slurry containment |
| Track System | Bolt-mounted steel guide tracks for straight, true cuts |
What safety rules apply to wall sawing in Qatar?
Wall sawing operations at Aseel Constructions follow strict safety protocols in accordance with Qatar's construction regulations. Operators are trained in wall saw operation and hold valid safety cards. We prepare a method statement and risk assessment for every project. Remote-controlled operation keeps personnel at a safe distance from the cutting zone. Water management systems prevent slip hazards, and all cut sections are supported or secured before final separation to prevent uncontrolled collapse.
Frequently Asked Questions
Our wall saws cut reinforced concrete up to 730mm deep. The usable depth depends on the setup and access. For anything thicker we cut from both faces and meet in the middle, combine wall sawing with core drilling at the corners, or switch to wire sawing.
We confirm the structural approach with the engineer during site assessment and plan the cut sequence before mobilizing equipment.
The diamond blade cuts straight through it. Industrial-grade segments on a wall saw blade are designed for continuous slicing through concrete and embedded steel without snagging.
What we don't do is run the saw into reinforcement we haven't mapped. On projects with high-density rebar or suspected PT cables, we recommend a GPR scan first, and we run one on request. It helps map embedded objects. The engineer must review the proposed cut path; scanning does not guarantee that every object has been detected.
Water runs continuously to the blade, cooling the diamond segments and suppressing concrete dust at the source. Slurry is channeled down the wall and collected using dams, vacuum hoses and absorbent matting.
On interior finishing-stage jobs in Doha, we wrap adjacent finishes in protective sheeting before starting. Slurry gets managed at the cut face, not mopped off finished floors twenty minutes later.
We estimate the time after reviewing the opening dimensions, wall thickness, reinforcement and access. Setup and lifting the cut section are part of the work.
Thicker walls, post-tensioned elements, or confined access will extend that estimate. We don't give timelines without seeing the wall and the drawings first.
Wall sawing produces noise. The site team should assess exposure and agree hearing protection and working hours before cutting starts.
For sensitive sites such as occupied hotels, hospitals and schools, we schedule cutting during agreed low-activity periods and confirm noise limits with the project manager before work starts.
Yes. We provide wall sawing 24/7 across Qatar, including Doha and Lusail. Call +974 7066 1660 for emergency mobilisation.