Concrete cutting across Qatar: where we work, and what changes by area
We work across almost all of Qatar from our base in Old Salata, Doha. Between areas, the structure, the access and the shift you are allowed to work change more than the price list does.
We are based at Concord Business Center on Al Meena Street in Old Salata, Doha, and we work across Qatar around the clock. Travel time is rarely the interesting part of a quote. What matters is what you are cutting into and who is standing next to it.
Below is what we have actually met in each area, drawn from jobs we have delivered. If your site is somewhere not on this list, it is still covered. Call and ask.
Lusail
For work in Lusail, send the structural drawings and opening positions before booking a crew. Our wall saws cut up to 730mm deep, and wire sawing is available for thicker sections. GPR scanning is available on customer request. Where post-tensioning is present, agree the investigation and cutting method with the structural engineer before work begins.
West Bay
West Bay work is mostly occupied office towers, which changes the job more than the concrete does. Permits, a booked hoist slot, floor protection over finished carpet, noise limits agreed with the building manager, and a full clean before tenants arrive. The cutting takes the same time it would on an empty site. Everything around it does not, which is why West Bay scopes are usually night shifts.
The Pearl
Residential towers, occupied floors, and finished surfaces on every side of the work. Slurry gets managed at the cut face here, not mopped off a marble floor twenty minutes later: sheeting, absorbent barriers, bunding at the door, and bagged slurry where drainage is limited. PT slabs throughout, so we recommend a GPR scan before any cutting.
Msheireb
Tight access and dense structure. Basement levels with restricted headroom mean standard core rigs will not stand up, so we run short barrels with extensions and reposition more often. Slower per hole, and worth knowing before you price the job.
Doha Industrial Area
This is where the high-volume work happens. Warehouse ground slabs, typically 150mm to 250mm with light mesh, open access, daytime shifts. One job here ran 180 penetrations through 250mm slabs in an empty unit. Per-hole cost drops sharply past about twenty holes in one location, because mobilisation and setup spread across all of them. Expansion joints in warehouse slabs are the other staple: a walk-behind saw covers 10 to 15 linear metres an hour at 50mm depth in C30.
Al Wakrah
More villa and low-rise work, and the concrete itself differs. Foundations here are often poured with local wadi aggregate, which behaves differently under a diamond bit than the C60 mixes in Lusail core walls. Aggregate type, cement content and compressive strength all decide which bond grade of diamond segment goes on the barrel.
Al Rayyan and Education City
Institutional and stadium work, including scopes delivered around the clock on the FIFA 2022 stadium programme. School and campus buildings usually mean working to a term calendar and around occupied blocks.
Al Khor
Northern coverage. Longer travel means mobilisation is a bigger share of a small scope, so batching penetrations into one visit matters more here than anywhere else.
Hamad International Airport
Floor sawing and core drilling delivered for Man Enterprise on airport expansion works. Airside and terminal environments mean permits, escorts and strict housekeeping.
Doha Metro
Diamond core drilling, GPR scanning and chemical anchor installation across stations for QDVC and Alstom. On rail infrastructure we recommend scanning first, because structural penetrations near live systems leave no room for a strike.
Mesaieed, Ras Laffan and Dukhan
Our crews work across almost all of Qatar, including the industrial cities of Mesaieed and Ras Laffan and the west coast around Dukhan. Industrial sites in these areas usually need gate passes, safety inductions and a permit to work before equipment goes in, so send the site contact and the induction requirements with your enquiry. The distance makes mobilisation a bigger share of a small scope, so group your penetrations into one visit where you can.
Frequently asked questions
Do you work outside Doha?
Yes, across almost all of Qatar, including Al Wakrah, Al Khor, Al Rayyan, Mesaieed, Ras Laffan and Dukhan. On longer trips mobilisation becomes a bigger share of a small scope, so batching penetrations into one visit saves more than it does inside Doha.
Which areas need a GPR scan before cutting?
GPR scanning is available on customer request across our service areas. For post-tensioned concrete or uncertain embedded services, discuss the scan scope and proposed openings with the structural engineer before cutting.
Can you work at night in occupied buildings?
Yes, and in West Bay and The Pearl it is usually the only option. Night work carries setup you do not need on an empty site: floor protection, agreed noise limits, a banksman for the hoist, and a full clean before tenants arrive.
How fast can you get to site?
Most enquiries get a first response inside two hours, and we mobilise 24/7 across Qatar. For urgent scopes inside Doha same-day is normally possible once the permit is in place.
Tell us where the site is.
Send the drawing and the floor level and we will price it properly. Most enquiries get a first response inside two hours.
Second line: +974 5077 6363. Email info@smartcutqa.com.
Related pages
Choose from our concrete cutting services, including floor and road sawing and GPR scanning on request. Our quote guide explains which site details to send.