Floor Sawing and Road Cutting Services in Qatar
Joints, trenches and slab sections in concrete and asphalt, up to 500mm deep, with walk-behind and ride-on saws.
Floor sawing at Hamad International Airport for Man Enterprise and at Mall of Qatar for Interprogetti.
Floor and road sawing in Qatar for expansion joints, utility trenches, slab sections and road repair boundaries, cutting concrete and asphalt up to 500mm deep. We run walk-behind saws for interior slabs and tight basements, and ride-on saws for the long cuts on roads, car parks and warehouse floors.
Joint cutting is the volume work. At 50mm depth in C30 concrete, one walk-behind saw covers 10 to 15 linear metres an hour. All cutting is wet, and the slurry is vacuumed up at the blade so it does not run into drains or across finished floors.
How does floor and road sawing work?
Site Survey & Marking
Our team inspects the surface, identifies any subsurface utilities or reinforcement, and marks the cut lines with chalk lines or laser guides.
Equipment Selection
Based on the material type, required depth, and project scale, we select the saw: walk-behind for precision work or ride-on for high-volume cutting.
Wet Diamond Cutting
The diamond blade engages the surface with continuous water flow for cooling and dust suppression. The operator guides the saw along the marked lines at controlled speed and depth.
Slurry Management & Cleanup
Cutting slurry is captured and contained using vacuum recovery systems. The work area is cleaned, and all waste is disposed of in compliance with environmental regulations.
Where is floor and road sawing used?
Expansion Joint Cutting
Precise control joints and expansion joints in newly poured concrete slabs to manage cracking and thermal movement in floors and pavements.
Utility Trenches
Straight, clean-edged trenches in concrete and asphalt for installing water, gas, electrical, and telecommunications services.
Road Repair Cuts
Neat boundary cuts that define repair patches in roads and highways and leave clean edges for asphalt or concrete patching.
Floor Removal Sections
Cutting floor slabs into manageable sections for removal during renovation, basement excavation, or foundation modification work.
Slab Modification
Precision cuts for modifying existing floor slabs, creating openings for new equipment foundations, pits, or drainage channels.
Cable & Pipe Trenching
Narrow, precise trenches cut into concrete floors for routing electrical cables, data lines, plumbing, and fire suppression piping.
How deep can you cut a floor or a road?
| Specification | Details |
|---|---|
| Maximum Cut Depth | Up to 500mm |
| Material Types | Reinforced concrete, plain concrete, and asphalt |
| Saw Types | Walk-behind saws and ride-on saws |
| Cutting Method | Wet cutting with continuous water supply |
| Slurry Management | Vacuum recovery and containment systems |
| Blade Technology | Diamond blades optimized for concrete and asphalt |
| Applications | Joints, trenches, patches, removal cuts, and modifications |
What safety and traffic rules apply on Qatar roads?
Floor and road sawing operations by Aseel Constructions follow Qatar's road safety and construction site regulations. Operators wear full PPE, including high-visibility clothing for road work, and work on public roads runs under a traffic management plan. We carry out a risk assessment before every project, use utility detection methods to avoid subsurface services, and contain slurry so it does not reach drains. Equipment is inspected and maintained on a regular schedule.
Frequently Asked Questions
Concrete is harder and more abrasive on the diamond matrix, so you run slower with a blade rated for the concrete's compressive strength and rebar density. Asphalt is softer and stickier, especially in Qatar's summer heat when surface temperatures exceed 60 degrees Celsius. At that temperature asphalt gets gummy, loads the segment differently, and can close kerf if you go too slow.
We carry separate blade stocks for each material and check conditions before setting blade speed and water flow.
Our saws reach up to 500mm depth in a single pass using large-diameter blades. Most commercial floor slabs in Qatar run 150mm to 250mm, so 500mm capacity covers nearly all standard applications without multiple passes.
For cuts into thick raft foundations, we combine flat sawing with core drilling at the start and end to give the blade a clean run. Depth requirements are confirmed on-site before pricing.
Walk-behind saws stop a few centimetres short of a wall, column base or existing joint. For cuts that need to terminate at a wall or reach into a corner, we finish with a core drill or hand saw to complete the line without overcutting.
We don't drive saws past the marked line to save time. Overcuts into adjacent panels create crack initiation points that show up months later in the finished floor.
At 50mm depth in standard C30 concrete, a walk-behind saw covers 10 to 15 linear meters per hour. A 5000m2 warehouse with joints on a 6m grid has about 1,670 linear meters to cut. At 10 to 15 meters an hour per saw, that is 110 to 170 saw-hours, so it is a significant programme.
We address it with multiple saws running in parallel, working around freshly poured bays on phased pours. Give us the floor layout and pour schedule and we'll plan the joint cutting to stay ahead of the concrete contractor.
Yes. We cut both asphalt and concrete road surfaces across Qatar: precise lines for utility installation, road marking removal and pavement repair, plus asphalt cutting and trench cutting for service lines.
Outdoor work in direct sun is restricted. Under Ministerial Decision No. 17 of 2021, the Ministry of Labour bans outdoor work between 10:00 and 15:30 from 1 June to 15 September, and work in open areas also stops when the WBGT heat index passes 32.1 degrees Celsius. We plan road and car park cutting for early morning or evening in those months. Check the Ministry of Labour for the notice that applies in the current year.
Related Services
Further reading
For uncertain embedded services, ask about GPR scanning on customer request. See our Qatar service areas and pre-cut safety checklist when planning access and work boundaries.